BENTLY 167699-02 Interface Module
1900/65A packaged, independently installed monitor
1900/65A-01-01-00-00-00 • Continuous monitoring and protection, suitable for automatic shutdown applications
• 4-channel vibration input (2-wire and 3-wire speed and acceleration sensors, as well as Bently Nevada eddy current sensors)
• Up to 4 variables per channel, with independent integration and filtering control
• Some variables have filtering up to eight poles
24 bit A/D converter with 25 kHz bandwidth
4 channel temperature input (E, J, K, and T type thermocouples)
• Level 2 alarm – ALERT and DANGER
6 configurable relays with voting logic
Buffered sensor output -4 monitor outputs, 1 display device output
4 configurable 4-20 mA recorder outputs
• Configuration software for individual applications
Receive 18 to 36Vdc power supply; Provide a 110/220Vac external power supply
Can be installed through DIN rail brackets or mounting wall panels
Compact structure – its size is (inches):
Monitor: 7.75 x 5.88 x 2.93
Display device: 7.75 x 5.03 x 1.29
Monitor with display device: 7.75 x 5.88 x 3.85
Optional fiberglass cover or steel protective door (for panel installation) to meet environmental protection installation requirements and IP65
• Pending hazardous area permits, including CSA (Class 1, Zone 2- although monitors cannot be installed in Class 1 areas, they support sensors installed in Zone 1 through insulation and barriers), ATEX
(Zone 2), CE and GOST (IEC Ex)
The GE/Bently Nevada 3500/05 system rack design can accommodate all 3500 monitor modules and rack power supplies. It allows various 3500 modules to communicate with each other and allows power to be allocated to each module as needed. Full size rack: 19 inch EIA rack with 14 available module slots 2. Mini rack: 12 inch rack with 7 available module slots. 3500 racks are manufactured in three formats: 1. Panel installation: This rack format is installed on a rectangular cut in the panel and secured to the panel using the fixture provided with the rack. The wiring connections and I/O modules can be operated from the rear of the rack.
2. Rack installation: This rack format installs 3500 racks on 19 inch EIA rails_ On. The wiring connections and I/O modules can be operated from the rear of the rack. 3. Partition installation: When it is not possible to operate from the rear of the rack, this rack format can install the rack on a wall or panel. The wiring connections and I/O modules can be accessed from the front of the rack. The 3500/05 micro rack does not have this format. The power supply and rack interface module must be located in the leftmost rack position. The remaining 14 rack positions (7 rack positions for micro racks) can be used for any module combination.
Features: – accommodates all 3500 monitor modules and rack power supplies – Manufactured in (2) sizes: Full size rack and micro rack in (3) formats: Panel mounted, rack mounted, and partition mounted -7 or 14 rack positions
A cycle time of L 25 seconds. By introducing high-performance PLC, 125840-02 has expanded its modular control system for PLC and motion control tasks. The characteristic of high-performance PLC is its compact design, which is part of the controller PLC series. The I/O module can be directly connected to the controller PLC without the need for additional bus couplers. The control concept of high-performance PLC can be fully integrated into all Bau ü ller control platforms, and its software is 100% compatible. The controller PLC series has up to five different fieldbus module interfaces for PLCs.
[Disclaimer]
Our company sells new products and discontinued products, and purchases such special products through independent channels. Guizhou Yuanmiao Automation Equipment Co., Ltd. is not an authorized distributor, distributor or representative of the featured products of this website. All product names/product images, trademarks, brands and microlabels used on this website are the property of their respective owners. Product descriptions, descriptions or sales with these name images, trademarks, brands and logos are for identification purposes only and do not represent any association or authorization with any right holders.
